car wont go into gear after clutch install

2005 BMW 330Ci Japan Red Tan interior. The car starts moving if you push it to 1st.

Troubleshooting Common Clutch Issues And Causes Haynes Manuals

2014 Mazda 3 Sport 20 6MT.

. Discussion Starter 1 Mar 9 2016. During such the salve naturally extends fully. Wont go into gear.

If your vehicle is no longer going into gear after a clutch service it may be possible that an issue occurred while the service was being done. 4 Have clutch fluid and bled the clutch afterwards. 2006 Honda Accord EX 6.

How to bleed the clutch system. If the clutch fluid ever ran dry then the clutch hydraulics will need to be bled of air. Just changed my clutch.

How to fix a car that wont go into gear DIY with Scotty Kilmer. Only show this user. The car will shift fine once you are moving it will go into 1st-5th gears just fine if the car comes to a dead stop it.

I called the mechanic and hes saying its my fault cause I bought a used pressure plate. A clutch job is performed and during such the clutch slave cylinder is removed. Besides pulling out of first gear will feel harder than normal.

Car wont go into gear while the engine is running after new clutch install. The last time I had a mustang shop bleed it and it was OK for a week alittle notchy but going in gear. My car wouldnt want to go into first cause it would grind.

Now it will not go into gear. 6 Check to see if the clutch slave moves the clutch fork when you step on the clutch. What do I do I dont want to pay another 1300 for a clutch install.

Replaced Clutch car wont shift into gear. How to replace clutch master cylinder. Perhaps a problem with the clutch fork or hydraulic clutch mechanism that is used to disengage the clutch so that the transmission can be shifted.

Put it all back together and the shifter goes through all the gears no trouble but when turned on will not go into any gear. 2 of 2 Go to page. The clutch isnt disengaging it seems.

Pulling everything apart was pretty easy. It wont come out of the reverse gear. Joined Sep 13 2009.

Put it in reverse turned it around drove it back. All gears engaged perfectly fine. It could be possible that the mechanism is.

The clutch is much more likely to be the problem than the transmission. When the car was raised front end up still and put together enough. 121613 UPDATE SOLUTION - THE CLUTCH PEDAL NEEDED TO BE ADJUSTED.

The transmission will shift in and out of gear without any issue when the car is not running. However if it goes into gear DO NOT start the car without taking it back out of gear. They said the clutch is good it has to be in the hydraulics.

The slave is reinstalled and new we push the slave into place. He may or may not have a defective unit. The signs that the car will show at this time are.

Could be that they destroyed an O-ring when installing the master cylinder. 04-29-2014 0839 PM 8. Adjusted the pedal even put a new slave cylinder on in case it was that.

The transmission wont shift and the car makes a grinding sound when the engine is running. I installed a ACT xtreme duty clutch on my 02 wrx and ever since Ive had it installed it wont go into gear while the engine is running and the car is not moving. 4 Nov 11 2010.

Put it into gear drove it for about 50 feet in first. Otherwise the problem could be the clutch master cylinder slave cylinder or throwout bearing. Jump to Latest Follow Hey everyone.

Since the car went into gear and drove easily when I first started it can I pretty much. 2 Torqued the pressure plate onto the flywheel to spec. Up to 25 cash back Transmission stuck in gear after clutch install.

Ive done that before no pressure. After clutch replacement hard to shift into gear Transmission ATMT Driveline Welcome to the North American Subaru Impreza Owners Club. The car will shift through all gears fine when turned off but when I start it in neutral and push the clutch in it won.

Either way modular clutch or not the transmission has to be removed. After some 20 miles on the road the car stopped getting into gears again and then ended up stuck in 3rd. Voting is now live for Aprils E46 of the Month Challenge.

Mechanic test drove the car. I get in car turn motor on depress clutch but cant shift into any gear. Tighten to around 9lbs of torque at first for the linkage.

Our car wouldnt get into gears with engine on engine off was fine mechanic said we needed a new clutch. There is either still air in the clutch system you have a bad master or slave cylinder the clutch isnt right or the TOB isnt right. So I just put a new clutch in my 01 Mustang with the baby 38l engine and a 5 speed T5OD transmission.

I made it to my house and now my car wont go into first gear. Up to 8 cash back Hello. 3 Resurfaced the flywheel if it is too worn.

Up to 8 cash back on September 09 2016. The clutch job is performed. Just finished a clutch replacement about my 20th one however when starting the car and depressing the clutch it will not go in gear.

Then it gets bad again. Im going to bleed the slave clutch cable seems fine. 21 - 26 of 26 Posts.

Sometimes its impossible to go into 1st or reverse. I looked under the car and saw a puddle of brake fluid and figured it out from there. He said it would take a day but ended up taking 3 days apparently the job was bigger than he thought.

The clutch kit was brand new flywheel was resurfaces pivot ball. Parks and turns off car for me to test it out. I shut off the car put it in first and started it with the clutch in.

If the vehicle was shafting fine prior to installation or was able to be driven whether the clutch was slipping or not and now the vehicle will not move at all the issue is with the workmanship or the clutch set itself. Ill do that before I install the engine back into the car. 5 Make sure the throw out bearing is attached to the clutch fork correctly.

Well the clutch isnt releasing fully which is why it wont go into gear with the engine running. Now newer brake fluid is allowed to come down the line and the clutch replacement commences. Dougdye325 Premium Member.

Thank you Rod Knox But on a separate issue Ive got grindingscraping in first second and third which got better with the new clutch and bearing install but still quite bad in first and second So before this new clutch install the car was making this grindingscraping noise. Rslainhart September 1 2016 441pm 1. Checked CMC and slave for leaks and didnt find.

Only show this user. It will sometime go into 4th but grind or clunk pretty badly and the car will lurch forward.

How To Replace A Car Clutch Step By Step Guide Bumbleauto